Sandwich ELISA to human ATP1B1 AEE0019

560,00800,00

ELISA kit for human ATP1B1, with data demonstrating no cross-reactivity to other closely related proteins.

Description

ATP1B1

All names and symbols: ATPase Na+/K+ transporting subunit beta 1; Sodium/potassium-dependent ATPase subunit beta-1; ATP1B; ATP1B1

Confirmed species reactivityHuman
Sensitivity0.066 ng/ml
Linear calculation range0.156 – 5 ng/ml
Precision intra-assay / inter-assay<10% / <12%
Aeonian Rating®90
RRID
MatrixRecovery Range (%)Average (%)
Serum (n=5)83-9991
EDTA plasma (n=5)80-10090
Heparin plasma (n=5)82-9990
Recovery: Matrices were spiked with recombinant ATP1B1 and the recovery rates were calculated by comparing the measured value to the expected amount of ATP1B1 in the matrices.
Matrix1:21:41:81:16
Serum (n=5)87-109%74-104%90-94%86-108%
EDTA plasma (n=5)86-101%90-101%78-110%84-96%
Heparin plasma (n=5)90-101%77-107%93-96%89-109%
Linearity: The linearity of the kit was assayed by testing serially diluted matrices spiked with a fixed amount of recombinant ATP1B1. The results were demonstrated by the percentage of calculated concentration related to the expected concentration of ATP1B1 in the diluted matrices.

Calibratrion curve:

AEE0019 to ATP1B1 was successfully used to determine the concentration of ATP1B1 in serum, plasma and buffer. Recommended serum dilution 1:8, EDTA plasma dilution 1:4, and heparin plasma 1:8.

Calibration curve of recombinant ATP1B1 in buffer. HRP detection by Absorbance at 450nm.

Selectivity of the ELISA kit:

AEE0019 to ATP1B1 was successfully confirmed selective as there were no signals found in the presence of other closely related proteins at high and low concentrations.

Selectivity was tested by comparing the signals of recombinant ATP1B1 with other closely related recombinant proteins, each at two concentrations. The other related proteins tested were ATP1A1, and ATP1B2. HRP detection by Absorbance at 450nm.

ELISA Test:

The microtiter plate provided in this kit has been pre-coated with an antibody specific to ATP1B1. Standards or samples are then added to the appropriate microtiter plate wells with a biotin-conjugated antibody preparation specific to ATP1B1. Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. After TMB substrate solution is added, only those wells that contain ATP1B1, biotin-conjugated antibody and enzyme-conjugated Avidin will exhibit a change in color. The enzyme-substrate reaction is terminated by the addition of sulphuric acid solution and the color change is measured spectrophotometrically at a wavelength of 450nm ± 10nm. The concentration of ATP1B1 in the samples is then determined by comparing the O.D. of the samples to the standard curve.

ELISA Procedure:

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 2 hours at 37℃;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37℃;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 1 hour at 37℃;
6. Aspirate and wash 5 times;
7. Add 90µL Substrate Solution. Incubate 15-25 minutes at 37℃;
8. Add 50µL Stop Solution. Read at 450nm immediately.

Stability:

The stability of ELISA kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage conditions.
Note:
To minimize unnecessary influences on the performance, operation procedures and lab conditions, especially room temperature, air humidity and incubator temperatures should be strictly regulated. It is also strongly suggested that the whole assay is performed by the same experimenter from the beginning to the end.

Product Manual Traditional
Product Manual Ready to Use
Material Safety Data Sheet Traditional
Material Safety Data Sheet Ready to Use

Additional information

DL-ATP1B1-Hu (traditional) T96

Composition:
Pre-coated, ready to use 96-well strip plate 1
Plate sealer for 96 wells 2
Standard 2
Diluents buffer 1×45ml
Detection Reagent A 1×120μl
Detection Reagent B 1×120μl
TMB Substrate 1×9ml
Stop Solution 1×6ml
Wash Buffer (30 × concentrate) 1×20ml
Instruction manual 1

DL-ATP1B1-Hu (traditional) T48

Composition:
Pre-coated, ready to use 96-well strip plate 1
Plate sealer for 96 wells 2
Standard 2
Diluents buffer 1×22.5ml
Detection Reagent A 1×60μl
Detection Reagent B 1×60μl
TMB Substrate 1×4.5ml
Stop Solution 1×3ml
Wash Buffer (30 × concentrate) 1×10ml
Instruction manual 1

DLR-ATP1B1-Hu (ready-to-use) T96

Composition:
Pre-coated, ready to use 96-well strip plate 1
Plate sealer for 96 wells 2
Standard 2
Standard Diluent 1×20ml
Detection Solution A 1×12ml
Detection Solution B 1×12ml
TMB Substrate 1×9ml
Stop Solution 1×6ml
Wash Buffer (30 × concentrate) 1×20ml
Instruction manual 1

DLR-ATP1B1-Hu (ready-to-use) T48

Composition:
Pre-coated, ready to use 96-well strip plate 1
Plate sealer for 96 wells 2
Standard 2
Standard Diluent 1×10ml
Detection Solution A 1×6ml
Detection Solution B 1×6ml
TMB Substrate 1×4.5ml
Stop Solution 1×3ml
Wash Buffer (30 × concentrate) 1×10ml
Instruction manual 1

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

SKU: AEE0019 Category: